Maxx Line Plus Tankers
As an enhancement of the Maxx Line, the Maxx Line Plus range impresses with its standard equipment and value.
This includes a wide, high-volume tyre for improved driver comfort and reduced soil-compaction. Another benefit is the option of a centrally-mounted turbo-filler under the tank, for boosted filling speeds on both sides of the tanker, even with a suction arm (for vacuum tanker models).
Tandem Axle
- 12,000l Vacuum or Pump
- 14,000l Vacuum or Pump
- 16,000l Vacuum or Pump
- 18,000l Vacuum or Pump
- 20,000l Vacuum or Pump
-
- Tandem chassis
- Fully galvanised steel tank of chosen volume
- Ball head K80 (Ø 80mm)
- Drawbar suspension incl. tank tipping cylinder and mechanical drop support jack
- Hydraulic single-line brake or compressed air brake system with ALB
- Gigant or Gigant Plus parabolic suspension (model dependent)
- Trailing axle: 2 brake axles, front axle rigid, rear axle trailed, hydraulically lockable max. speed of 60 km/h
- Axle type: BPW 410 x 180 brake drums (from 14,000ltr models)
- Tyres 750/60 R30.5, max. load per wheel 6740 kg at 40 km/h, spring centre: 900 mm
- 40 km/h version incl. mudguards, underride guard and side marker lights
- Wheel arch (less volume with wheel arch)
- 12,000 litre Hertell compressor max. 540 or 1000 rpm, heat-resistant
- 8" flange front center under the tank
- Blind flange 8" rear
- 6" suction slider with quick coupler, left
- Prepared for top-fill opening Ø=400 mm (in the front)
- Fill level indicator
- Siphon
- Foam separator
- Silencer with oil separator for compressor
- Rear-mounted hydraulic slider
- Hydraulic tapered rotary valve
- Hose holder (not possible in combination with drag shoe or dribble bar distributor)
- Continuous and robust angular frame
- 12V LED lighting with 7-pin connector
- 2 or 3 internal baffle plates (model dependent)
- 600 mm rear access hatch
- PTO drive shaft, wide angle one side
- Brackets in preparation for distribution attachment (drag shoe, dribble bar or disc injection)
-
Equipment Upgrades
- Piton-Fix (Ø 50 mm)
- Pivoting drawbar eye (Ø 50 mm)
- Drawbar with swivelling eye (Ø 51 mm)
- Forced steering: 2 brake axles, front rigid, rear steered K50
- 13,000l Battioni vacuum compressor, 540 or 1000 rpm
- 8" suction slider with quick coupler, left
- Hydraulic top-fill opening Ø=400mm with ladder on left/right
- Internal agitator (with air), including drain tap and hose on siphon
- Hydraulic turbo-filler under the tank
- Lubrication block on 2 lubrication points for tandem chassis
- Four-point hydraulics: lifting force 2000 kg Cat. 2
- Four-point hydraulics: lifting force 4500 kg Cat. 3
- 8" suction nozzle, incl. compressor changeover and docking station, left/right in direction of travel
- Hydraulic discharge accelerator fitted behind tank for slurry
- Hydraulic discharge accelerator with shredding cutter fitted behind tank for slurry
- Various pipe and hose length options
- 5-way or 6-way control block options with load sensing
-
- Tandem chassis
- Fully galvanised steel tank of chosen volume
- Ball head K80 (Ø 80mm)
- Drawbar suspension incl. tank tipping cylinder and mechanical drop support jack
- Hydraulic single-line brake or compressed air brake system with ALB
- Gigant or Gigant Plus parabolic suspension (model dependent)
- Trailing axle: 2 brake axles, front axle rigid, rear axle trailed, hydraulically lockable max. speed of 60 km/h
- Axle type: BPW 410 x 180 brake drums (from 14,000ltr models)
- Tyres 750/60 R30.5, max. load per wheel 6740 kg at 40 km/h, spring centre: 900 mm
- 40 km/h version incl. mudguards, underride guard and side marker lights
- Wheel arch (less volume with wheel arch)
- Pre-fitted for approx. 600 x 600 mm sliding cover
- Pump Models: Armatec eccentric screw pump 4000l with stone trap
- 6" suction slider with quick coupler, left
- Fill level indicator
- Hydraulic tapered rotary valve
- Hose holder (not possible in combination with drag shoe or dribble bar distributor)
- Continuous and robust angular frame
- 12V LED lighting with 7-pin connector
- 2 or 3 internal baffle plates (model dependent)
- 600 mm rear access hatch
- PTO drive shaft, wide angle one side
- Brackets in preparation for distribution attachment (drag shoe, dribble bar or disc injection)
-
Equipment Upgrades
- Piton-Fix (Ø 50 mm)
- Pivoting drawbar eye (Ø 50 mm)
- Drawbar with swivelling eye (Ø 51 mm)
- Forced steering: 2 brake axles, front rigid, rear steered K50
- Armatec eccentric screw pump 6000 l with stone trap
- Wangen eccentric screw pump 4000 l with stone trap, 6" quick coupler left
- Wangen eccentric screw pump 4000 l with stone trap, 6" quick coupler left
- 8" suction slider with quick coupler, left
- Sliding cover approx. 600 x 600 mm hydraulic front incl. ladder and position display
- Lubrication block on 2 lubrication points for tandem chassis
- Four-point hydraulics: lifting force 2000 kg Cat. 2
- Four-point hydraulics: lifting force 4500 kg Cat. 3
- 8" suction nozzle with docking station, right/left in direction of travel, incl. pump case
- Various pipe and hose length options
- 5-way or 6-way control block options with load sensing
-
- Digital flow meter ISOBUS. Shows m³/ha and m³/min. and the suggested driving speed to reach the specified m³/ha (tractor with ISOBUS and TECU as per AEF required)
- Preparation for MCS EVO NIR sensor incl. bracket (only in combination with ISOBUS digital flow meter or DMR flow rate control), without NIR sensor and without MCS controller
Slurry Tanker Configurator
Other Slurry Tanker Models
-
Maxx Line Range
Offering the largest selection of sizes and equipment, a vacuum or pump tanker from the Maxx Line range can be configured to suit all budgets and needs. -
Alpha Line Range
The Alpha Line slurry tanker was designed especially for intensive, contractor-level use. It features an extensive range of standard equipment, which can be customized for use with the latest slurry application technology.